A dripping faucet wastes more water than most homeowners realize. According to the U.S. Environmental Protection Agency, a single leaky faucet dripping once per second can waste more than 3,000 gallons of water per year. Whether your faucet is past its prime, you’re upgrading to a new fixture, or you’ve just remodeled your kitchen or bathroom, getting the installation done correctly the first time matters.
At Pike Plumbing & Sewer, Anthony Estrella and Corey Moline bring 30+ years of combined plumbing experience to every job. Faucet installation is one of the most common services we handle — and one of the most commonly botched when it’s done without the right tools or knowledge.
Key Takeaway
A properly installed faucet prevents leaks, protects your cabinetry and walls from water damage, and ensures your fixture performs the way the manufacturer intended. It’s not just about turning a wrench — it’s about getting the connections, supply lines, and shutoff valves right.
Installation of Faucet In Your Kitchen or Bathroom
Kitchen and bathroom faucet installations are not the same job. The fixtures differ in size, water pressure requirements, and how they connect to your existing plumbing. Getting the wrong approach for the wrong room creates problems that show up later — slow leaks behind the wall, loose handles, or supply line failures under the sink.
Faucet Installation Service in Kent, WA
When we arrive for a faucet installation in Kent, we don’t just swap the fixture and leave. We inspect the shutoff valves under the sink, check the condition of the supply lines, verify water pressure at the connection point, and confirm the drain assembly is properly sealed. These are the steps that separate a lasting installation from one that needs attention again in six months.
Kitchen Faucet Installation
Kitchen faucets carry higher daily use than almost any other fixture in the home. Pull-down sprayers, single-handle designs, two-handle configurations, pot fillers — the variety of kitchen faucet styles has expanded significantly, and each one has specific installation requirements.
- Deck plate and hole configuration: Some kitchen sinks have one pre-drilled hole, others have three or four. The faucet you choose must match your sink’s hole pattern, or a deck plate is required to cover unused holes.
- Supply line connections: Braided stainless steel supply lines are the current standard. We will discuss replacement of old plastic or corrugated lines at the time of installation to prevent future failures.
- Shutoff valve condition: Older shutoff valves can seize or fail when turned off for the first time in years. We assess valve condition before the job starts.
- Spray hose routing: Pull-down and pull-out sprayer hoses require proper routing inside the cabinet to prevent kinking and ensure smooth retraction.
If you’re also installing a new kitchen sink alongside the faucet, our team handles both in a single visit. See our kitchen sink installation page for more detail on that process.
Bathroom Faucet Installation
Bathroom faucets come in widespread, centerset, and single-hole configurations. The right choice depends entirely on your sink’s existing hole pattern and the countertop or vanity you’re working with. Widespread faucets — where the handles and spout are separate pieces — require precise spacing and more involved under-sink work than a standard centerset.
- Widespread faucets: Handles mount 8 inches apart center-to-center. The supply lines run separately from each handle to the spout body, requiring more careful routing.
- Centerset faucets: Handle and spout are a single unit. These fit sinks with holes spaced 4 inches apart and are the most common configuration in standard bathrooms.
- Single-hole faucets: Increasingly popular in modern vanity designs. Some include a deck plate to cover a three-hole sink.
“Maxx was amazing at installing a new water heater, faucet in the kitchen, and water reducer value. He was quick and precise and my house is back to normal.” — Vanessa Baez, 5-star, Google review
Beyond the fixture itself, bathroom faucet installations often reveal underlying issues — corroded shutoff valves, old supply lines, or drain assemblies that need replacing. We address these at the time of installation so you’re not dealing with a follow-up call.
Faucet Plumbers in Your Area
What Sets Our Faucet Plumbers Apart
We don’t subcontract our faucet work. When you schedule with Pike, one of our licensed plumbers — including Anthony, Corey, Maxx, or Deven — handles the job directly. Our team’s 30+ years of combined experience means we’ve seen every faucet configuration, every corroded shutoff, and every supply line setup that exists in homes across the Kent, Bellevue, and Everett areas.
Pike is also a member of the local Chamber of Commerce — a reflection of our roots as a genuine local business, not a franchise operation passing through.
The Faucet Installation Process Step by Step
Here’s what happens when we show up for a faucet installation:
- Shutoff and pressure check: We shut off the water supply and verify the shutoff valves operate correctly. Stuck or corroded valves get addressed before anything else.
- Old fixture removal: We disconnect and remove the existing faucet, including the supply lines and any deck plate hardware.
- Connection point inspection: We inspect the sink deck, faucet holes, and drain assembly for corrosion, cracks, or sealant failure.
- New faucet mounting: The new fixture is mounted and secured according to the manufacturer’s specifications. We use the correct hardware — no improvised solutions.
- Supply line installation: Braided stainless supply lines are connected at both the shutoff valve and the faucet inlet. We check torque on every connection.
- Pressure test: Water is restored and we run the faucet through its full range — hot, cold, and mixed — while checking every connection point for any sign of moisture.
- Final inspection: We confirm the spray function (if applicable), handle operation, and drain flow before we pack up.
Key Takeaway
Most faucet failures trace back to supply line connections or shutoff valves that weren’t properly inspected at installation. A thorough process upfront prevents the slow leaks that damage cabinets and floors over time.
Types of Faucets We Install
| Faucet Type | Common Location | Key Installation Consideration |
|---|---|---|
| Single-hole / single-handle | Kitchen, bathroom | Deck plate may be needed for multi-hole sinks |
| Centerset (4" spread) | Bathroom vanity | Handles and spout are one unit; straightforward install |
| Widespread (8" spread) | Bathroom vanity | Separate handle and spout connections; more supply line routing |
| Pull-down / pull-out sprayer | Kitchen | Hose routing inside cabinet must prevent kinking |
| Wall-mount faucet | Kitchen, laundry, specialty bath | Requires access to in-wall supply lines; more involved rough-in |
| Pot filler | Kitchen (above range) | Requires a dedicated supply line run to the installation point |
| Bar / prep sink faucet | Kitchen island, wet bar | Island installs may require supply line extension through cabinetry |
| Commercial-style kitchen faucet | Kitchen | Higher flow service details; verify supply line and shutoff valve capacity |
Faucet Material and Finish Considerations
The fixture finish you choose — brushed nickel, matte black, polished chrome, oil-rubbed bronze — doesn’t change the plumbing work, but the internal valve cartridge and body material do matter for longevity. Brass-bodied faucets with ceramic disc cartridges are the most durable option for high-use locations like the kitchen. We’re happy to discuss what you’re considering before the installation day so we can confirm compatibility with your existing setup.
When to Replace Instead of Repair
Not every dripping faucet needs a full replacement. Sometimes a cartridge swap or a new O-ring fixes the problem. But there are situations where replacement is the right call:
- The faucet body is corroded or cracked
- Replacement cartridges for the model are no longer available
- The fixture is showing multiple failure points and has seen years of heavy use
- You’re remodeling and want the fixture to match new hardware
- The existing faucet has chronic low pressure that isn’t caused by the supply line
If you’re not sure whether repair or replacement makes more sense, our team can assess the fixture when we arrive and give you a clear recommendation before any work begins.
Faucet Installation for Bellevue, Everett, and King County Homeowners
Pike Plumbing & Sewer serves a wide area across King, Pierce, and Snohomish Counties. Our faucet installation service is available to homeowners and commercial property owners in Kent, Bellevue, Everett, Granite Falls, and the surrounding communities.
Serving Bellevue and the Eastside
Bellevue homes — especially those built during the rapid development of the 1980s and 1990s — often have original faucet fixtures that are well past their service life. Mineral buildup from the regional water supply accelerates wear on internal cartridges and valve seats. Supply line hardware in these homes is frequently original and overdue for replacement.
Serving Everett and Snohomish County
Everett and the broader Snohomish County area represent a growing part of our service territory. Homes in this region range from post-war construction to new builds, and faucet installation needs vary accordingly. Older homes may require shutoff valve replacement as part of the faucet job. Newer construction sometimes has rough-in configurations that require specific faucet body sizes.
Serving Granite Falls and Rural King County
In Granite Falls and the rural areas of King County, well water systems create different faucet wear patterns than municipal supply. Sediment and mineral content in well water is harder on cartridges and aerators. We factor in the local water source when assessing fixture condition and making installation recommendations.
Related Kitchen and Bathroom Plumbing Services
Faucet installation is often one part of a larger kitchen or bathroom project. We offer a full range of kitchen and bath plumbing services that pair naturally with faucet work.
Kitchen Sink Installation
Installing a new faucet at the same time as a new sink saves a service call and ensures everything is fitted and sealed together properly. Our kitchen sink installation service covers drop-in configurations with proper drain assembly and supply line connections.
Garbage Disposal Repair
Kitchen plumbing work often surfaces disposal issues at the same time. If your garbage disposal is underperforming or has failed, we can address it during the same visit as your faucet installation. Learn more on our garbage disposal repair page.
Shower and Bathtub Fixture Installation
If your bathroom remodel extends beyond the vanity, we also handle shower installation and bathtub installation, including the valve and trim work that connects to your water supply.
Water Leak Repair
A faucet installation visit sometimes reveals a slow leak that’s been hiding behind the cabinet. Our water leak repair service addresses supply line failures, shutoff valve leaks, and drain connection issues that show up during fixture work.
Fixture Installations
Beyond faucets, our fixture installation service covers sinks, shower hardware, and other plumbing fixtures throughout the home. If you’re doing a full bathroom or kitchen refresh, we can coordinate the full scope of fixture work in a single visit.
Why Choose Pike Plumbing & Sewer for Faucet Installation
There are a lot of plumbers in King County. Here’s what makes Pike Plumbing & Sewer a different choice.
Direct Experience, Not Subcontracted Work
Anthony Estrella and Corey Moline grew up as sons of tradesmen and built their skills from the ground up. They became friends working at another local plumbing company before founding Pike. When you call Pike, you get the people who built the company — not a rotating roster of subcontractors.
Over 5,000 Projects Completed
Pike has completed over 5,000 plumbing projects across the region. That volume means our team has handled nearly every faucet configuration, fixture brand, and under-sink situation that exists in homes and commercial properties across King, Pierce, and Snohomish Counties.
Licensed and Locally Committed
We hold Washington State plumbing license PIKEPPS782P7 and are members of the local Chamber of Commerce. We’re a real local business with a real address in Kent — not a lead aggregator or a franchise operation.
Rated Across Multiple Platforms
Pike Plumbing & Sewer has earned reviews across Google, Yelp, and Thumbtack from homeowners and commercial clients throughout the service area. Our reputation reflects the work Anthony and Corey put into every job — including the ones that don’t make headlines, like a faucet installation that just goes perfectly.
Frequently Asked Questions About Faucet Installation Service
How long does a faucet installation typically take?
Most standard faucet installations take between 45 minutes and 2 hours depending on the fixture type and the condition of the existing shutoff valves and supply lines. More complex installations — like wall-mount faucets or pot fillers requiring new supply line runs — take longer. We’ll give you a realistic time frame when we assess the job.
Do I need to buy the faucet before calling Pike?
You can, but it’s not required. If you’ve already purchased a fixture, we’ll install it. If you haven’t, we can discuss what configuration works best for your sink and water pressure setup before you buy. Bringing the wrong faucet for your sink’s hole pattern is a common and avoidable problem.
Will the shutoff valves need to be replaced during a faucet installation?
Not always, but it’s common in older homes. Shutoff valves that haven’t been operated in many years can seize or fail when turned off for the first time. We inspect valve condition before starting the job and let you know if replacement is warranted so there are no surprises.
Can Pike handle faucet installation in a commercial property?
Yes. We offer commercial plumbing services in addition to residential work. Commercial faucet installations — in office restrooms, commercial kitchens, or break rooms — follow the same thorough process we use on residential jobs. Contact us to discuss the scope of your commercial project.
What’s the difference between a faucet repair and a faucet replacement?
A repair addresses a specific failed component — a worn cartridge, a cracked O-ring, or a loose packing nut. A replacement removes the entire fixture and installs a new one. If the faucet body is corroded, the model is discontinued, or you want to upgrade to a new style, replacement is the right path. If the fixture is otherwise in good shape and only one component has failed, repair may be all that’s needed. Our team can assess the situation and give you a clear recommendation on the spot.
Ready to get your faucet installed right the first time? Call us or reach out through our online contact form. Anthony and Corey serve Kent, Bellevue, Everett, Granite Falls, and communities throughout King, Pierce, and Snohomish Counties.
Faucet Installation Service: Our 7-Step Process
Exactly what Pike Plumbing & Sewer does during every faucet installation — from shutoff to final inspection
Shutoff & Pressure Check
Water supply is shut off and shutoff valves are tested for correct operation. Stuck or corroded valves are addressed before anything else begins.
Old Fixture Removal
Existing faucet is disconnected and removed, including supply lines and any deck plate hardware.
Connection Point Inspection
Sink deck, faucet holes, and drain assembly are inspected for corrosion, cracks, or sealant failure.
New Faucet Mounting
New fixture is mounted and secured to manufacturer specifications using correct hardware — no improvised solutions.
Supply Line Installation
Braided stainless steel supply lines are connected at both the shutoff valve and faucet inlet. Torque is checked on every connection.
Pressure Test
Water is restored and the faucet is run through its full range — hot, cold, and mixed — while every connection point is checked for moisture.
Final Inspection
Spray function, handle operation, and drain flow are all confirmed before the job is complete. Most installations take 45 minutes to 2 hours.
Most faucet failures trace back to supply line connections or shutoff valves not properly inspected at installation. This 7-step process prevents the slow leaks that damage cabinets and floors over time.
Professional Faucet Installation by Pike Plumbing & Sewer
Done Right. Every Time.
